Certificate of Compliance

July 15, 2024

Part Number: 54-00283

Description: Connector, USB micro B jack, surface mount, through hole, 90°, nickel shell, IPX7 waterproof, reel


This is to certify that all articles listed above are compliant with all requirements and exemptions of the Directive (EU) 2015/863, and do not contain above the specified limits on any of the following banned substances:

  • Mercury (Hg): 0.1%
  • Polybrominated Biphenyls (PBB): 0.1%
  • Hexavalent Chromium (Cr6+): 0.1%
  • Cadmium (Cd): 0.01%
  • Polybrominated Diphenylethers (PBDE): 0.1%
  • Bis(2-Ethylhexyl) phthalate (DEHP): 0.1%
  • Benzyl butyl phthalate (BBP): 0.1%
  • Dibutyl phthalate (DBP): 0.1%
  • Diisobutyl phthalate (DIBP): 0.1%

Note: Products containing copper alloy (brass) connectors may contain up to 4% lead by weight. These components meet compliance through exemption 6(c) of Annex III. See below EU Waste Framework Directive (WFD) for article components with this exemption.


Tensility International Corporation certifies the above listed articles are fully compliant with the requirements of European Union Regulation (EC) 1907/2006 concerning the Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH).

Under REACH regulations – Article 7, Tensility International Corporation is considered a provider of "articles." All of our products are assemblies/components, not raw materials.  None of our products intentionally release substances into the environment.

Unless listed below, Tensility confirms our products do not contain any substances of very high concern (SVHC) above the specified limit, as updated January 23, 2024.

Tensility does not manufacture, use, or place on the market any substances, mixtures, and articles restricted under REACH Annex XVII, updated December 12, 2023.

Note: Copper alloy connectors may contain Lead (CAS No. 7439-92-1) in concentrations up to 4% by weight. According to ANNEX XVII Entry 63, paragraph 8(k)(iv), such articles fall within the scope of Directive 2011/65/EU and are excluded from REACH SVHC restrictions.



EU Waste Framework Directive (WFD) and SCIP Database

Article components containing SVHCs

Part Number: 54-00283
  • TARIC Code: 8536 9095
  • Material: brass (copper alloy)
  • SVHC: lead (CAS No. 7439-92-1)
  • SVHC Concentration: 4% by weight max
  • Article not manufactured in EU
  • No need to provide safe use information beyond the identification of the SVHC

  • Proposition 65 – California Safe Drinking Water and Toxic Enforcement Act

    WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

    EPA’s Toxic Substance Control Act Declaration

    Tensility declares that the above product complies with all applicable regulations established by the U.S. Environmental Protection Agency (EPA) under the Toxic Substances Control Act (TSCA).

    Inventory: All chemical substances in the listed product are included on the TSCA Inventory or are exempt from TSCA Inventory requirements.

    Significant New Uses (SNURs): The above product does not contain any chemicals introduced into commerce in a manner considered a "significant new use" under TSCA Section 5(a)(2).

    TSCA Section 8(a) Reporting: Tensility has complied with all applicable reporting requirements under TSCA Section 8(a) for the chemicals in the above listed product.

    Content of Concern:

    PBTs: Our review of material safety data sheets (MSDS) and supplier information indicates the above product does not intentionally contain any chemicals classified as Persistent, Bioaccumulative, and Toxic (PBTs) under TSCA.

    PFAS: FEP (fluorinated ethylene propylene) and PTFE (polytetrafluoroethylene) may be used in some Tensility components such as wire insulation or cable wrap, these materials are:

  • Established on the TSCA Inventory.
  • Not intentionally added to impart PFAS functionality to the final product.
  • Based on our review of material safety data sheets (MSDS) and supplier information, these materials do not exceed established regulatory thresholds for PFAS content.
  • Asbestos Free Product Declaration

    This document serves as a declaration and confirmation that asbestos materials are not utilized in any assembly, sub-assembly, or component of the products listed above. No asbestos is used at any time during the manufacturing and construction of our products unless otherwise stated.

    Declaration of PFAS

    The product(s) listed above have been assessed for the presence of PFAS, and it has been determined that they do not contain any PFAS compounds that are restricted under Annex XIV (the Authorization List) or Annex XVII (Restriction List) of the EU REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) Regulation (EC) No. 1907/2006.


    Luis Alcala
    Tensility International Corporation